ukl/development ecu02 boot successful 2020-09-02
Posted by Anonymous on Wed 2nd Sep 2020 14:31
raw | new post

barebox:/ reset


barebox 2016.06.0-EAG_2.02-g9917fe052de8 #1 Wed Sep 2 15:12:44 CEST 2020


Board: Eckelmann AG ECU02
mdio_bus: miibus0: probed
nand: ONFI flash detected
nand: NAND device: Manufacturer ID: 0x2c, Chip ID: 0xb1 (Micron MT29F1G16ABBEAH4), 128MiB, page size: 2048, OOB size: 64
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
m25p80 m25p80@20: mr25h256 (32 Kbytes)
imx-usb 53ff4400.usb: USB EHCI 1.00
netconsole: registered as netconsole-1
malloc space: 0x83efde40 -> 0x87dfbc7f (size 63 MiB)
running /env/bin/init...
Check if Memory is flashbased ...
__PASS__
USB: scanning bus for devices...
Bus 001 Device 001: ID 0000:0000 EHCI Host Controller
1 USB Device(s) found
USB: scanning bus for devices...
1 USB Device(s) found
running automount command 'usb && if [ -e /dev/disk0.0 ]; then mount /dev/disk0.0 /mnt/usbstorage; elif [ -e /dev/disk0 ]; then mount /dev/disk0 /mnt/usbstorage; fi' failed
USB: scanning bus for devices...
1 USB Device(s) found
running automount command 'usb && if [ -e /dev/disk0.0 ]; then mount /dev/disk0.0 /mnt/usbstorage; elif [ -e /dev/disk0 ]; then mount /dev/disk0 /mnt/usbstorage; fi' failed
USB: scanning bus for devices...
1 USB Device(s) found
running automount command 'usb && if [ -e /dev/disk0.0 ]; then mount /dev/disk0.0 /mnt/usbstorage; elif [ -e /dev/disk0 ]; then mount /dev/disk0 /mnt/usbstorage; fi' failed

Hit m for menu or any other key to stop autoboot:  1
blspec: blspec_scan_directory: nand loader/entries
USB: scanning bus for devices...
1 USB Device(s) found
USB: scanning bus for devices...
1 USB Device(s) found
running automount command 'usb && if [ -e /dev/disk0.0 ]; then mount /dev/disk0.0 /mnt/usbstorage; elif [ -e /dev/disk0 ]; then mount /dev/disk0 /mnt/usbstorage; fi' failed
USB: scanning bus for devices...
1 USB Device(s) found
running automount command 'usb && if [ -e /dev/disk0.0 ]; then mount /dev/disk0.0 /mnt/usbstorage; elif [ -e /dev/disk0 ]; then mount /dev/disk0 /mnt/usbstorage; fi' failed
Could not find Imagefile: /mnt/usbstorage/ecu02/root.ubi
UBI: scanning is finished
UBI warning: print_rsvd_warning: cannot reserve enough PEBs for bad PEB handling, reserved 16, need 20
UBI: registering /dev/nand0.root.ubi
UBI: registering root as /dev/nand0.root.ubi.root
UBI: attached mtd0 (name "nand0.root", size 80 MiB) to ubi0
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "root", R/O mode
UBIFS (ubi0:0): LEB size: 129024 bytes (126 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 78317568 bytes (74 MiB, 607 LEBs), journal size 9033728 bytes (8 MiB, 71 LEBs)
UBIFS (ubi0:0): reserved for root: 0 bytes (0 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 83ff209c, small LPT model

Loading ARM Linux zImage '/mnt/nand0-root/boot/zImage'
commandline:  console=ttymxc0,115200n8   lpj=995328 mtdparts=mxc_nand:1024k(barebox),1024k(bareboxenv),2432k(history),80M(root),-(var) console=null ro root=ubi0_0 rootfstype=ubifs ubi.mtd=3
Uncompressing Linux... done, booting the kernel.
Booting Linux on physical CPU 0x0
Linux version 4.9.0-g9398d97fa4b7 (ptxdist@ptxdist) (gcc version 5.4.0 (OSELAS.Toolchain-2016.06.0) ) #1 2016-06-01
CPU: ARM926EJ-S [41069264] revision 4 (ARMv5TEJ), cr=0005317f
CPU: VIVT data cache, VIVT instruction cache
OF: fdt:Machine model: Eckelmann AG ECU02
Memory policy: Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
Kernel command line:  console=ttymxc0,115200n8   lpj=995328 mtdparts=mxc_nand:1024k(barebox),1024k(bareboxenv),2432k(history),80M(root),-(var) console=null ro root=ubi0_0 rootfstype=ubifs ubi.mtd=3
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 120656K/131072K available (6090K kernel code, 525K rwdata, 1336K rodata, 424K init, 247K bss, 10416K reserved, 0K cma-reserved)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    vmalloc : 0xc8800000 - 0xff800000   ( 880 MB)
    lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
    modules : 0xbf000000 - 0xc0000000   (  16 MB)
      .text : 0xc0008000 - 0xc05faef8   (6092 kB)
      .init : 0xc07ca000 - 0xc0834000   ( 424 kB)
      .data : 0xc0834000 - 0xc08b7798   ( 526 kB)
       .bss : 0xc08b7798 - 0xc08f5458   ( 248 kB)
NR_IRQS:16 nr_irqs:16 16
MXC IRQ initialized
Switching to timer-based delay loop, resolution 15ns
sched_clock: 32 bits at 66MHz, resolution 15ns, wraps every 32292987384ns
clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 28740758601 ns
Console: colour dummy device 80x30
Calibrating delay loop (skipped) preset value.. 398.13 BogoMIPS (lpj=995328)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
ftrace: allocating 21751 entries in 64 pages
Setting up static identity map for 0x80008400 - 0x8000843c
devtmpfs: initialized
VFP support v0.3: not present
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302231375000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor ladder
No ATAGs?
imx25-pinctrl 43fac000.iomuxc: initialized IMX pinctrl driver
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
i2c i2c-0: IMX I2C adapter registered
i2c i2c-0: can't use DMA, using PIO instead.
pca953x 2-0020: failed reading register
i2c i2c-2: IMX I2C adapter registered
i2c i2c-2: can't use DMA, using PIO instead.
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
clocksource: Switched to clocksource mxc_timer1
NET: Registered protocol family 2
TCP established hash table entries: 1024 (order: 0, 4096 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
futex hash table entries: 256 (order: -1, 3072 bytes)
workingset: timestamp_bits=30 max_order=15 bucket_order=0
NFS: Registering the id_resolver key type
Key type id_resolver registered
Key type id_legacy registered
nfs4filelayout_init: NFSv4 File Layout Driver Registering...
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
io scheduler noop registered
io scheduler cfq registered (default)
imx-sdma 53fd4000.sdma: Direct firmware load for imx/sdma/sdma-imx25.bin failed with error -2
imx-sdma 53fd4000.sdma: external firmware not found, using ROM firmware
43f90000.serial: ttymxc0 at MMIO 0x43f90000 (irq = 61, base_baud = 4156250) is a IMX
console [ttymxc0] enabled
43f94000.serial: ttymxc1 at MMIO 0x43f94000 (irq = 48, base_baud = 4156250) is a IMX
50008000.serial: ttymxc3 at MMIO 0x50008000 (irq = 21, base_baud = 4156250) is a IMX
loop: module loaded
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xb1
nand: Micron MT29F1G16ABBEAH4
nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
5 cmdlinepart partitions found on MTD device mxc_nand
Creating 5 MTD partitions on "mxc_nand":
0x000000000000-0x000000100000 : "barebox"
0x000000100000-0x000000200000 : "bareboxenv"
0x000000200000-0x000000460000 : "history"
0x000000460000-0x000005460000 : "root"
0x000005460000-0x000008000000 : "var"
spi_imx 43fa4000.cspi: probed
libphy: Fixed MDIO Bus: probed
CAN device driver interface
flexcan 43f88000.can: device registered (reg_base=c891c000, irq=59)
flexcan 43f8c000.can: device registered (reg_base=c8924000, irq=60)
fec 50038000.ethernet (unnamed net_device) (uninitialized): Invalid MAC address: 00:00:00:00:00:00
fec 50038000.ethernet (unnamed net_device) (uninitialized): Using random MAC address: c2:4a:eb:d1:b1:ea
random: fast init done
libphy: fec_enet_mii_bus: probed
usbcore: registered new interface driver rt2800usb
usbcore: registered new interface driver rtl8192cu
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-mxc: Freescale On-Chip EHCI Host driver
usbcore: registered new interface driver usb-storage
ci_hdrc ci_hdrc.1: doesn't support gadget
ci_hdrc ci_hdrc.1: EHCI Host Controller
ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1
ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
rtc-pcf2123 spi0.3: clock was stopped. Time is not valid
rtc-pcf2123 spi0.3: spiclk 1039 KHz.
rtc-pcf2123 spi0.3: clock was stopped. Time is not valid
rtc-pcf2123 spi0.3: rtc core: registered rtc-pcf2123 as rtc0
i2c /dev entries driver
ad7414 0-0049: chip found
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on 53fb8000.esdhc [53fb8000.esdhc] using DMA
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
NET: Registered protocol family 10
sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
Key type dns_resolver registered
ubi0: attaching mtd3
ubi0: scanning is finished
ubi0 warning: ubi_eba_init: cannot reserve enough PEBs for bad PEB handling, reserved 18, need 20
ubi0: attached mtd3 (name "root", size 80 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 512
ubi0: VID header offset: 512 (aligned 512), data offset: 2048
ubi0: good PEBs: 640, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 14/8, WL threshold: 4096, image sequence number: 24264
ubi0: available PEBs: 0, total reserved PEBs: 640, PEBs reserved for bad PEB handling: 18
ubi0: background thread "ubi_bgt0d" started, PID 64
rtc-pcf2123 spi0.3: clock was stopped. Time is not valid
rtc-pcf2123 spi0.3: hctosys: unable to read the hardware clock
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "root", R/O mode
UBIFS (ubi0:0): LEB size: 129024 bytes (126 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 78317568 bytes (74 MiB, 607 LEBs), journal size 9033728 bytes (8 MiB, 71 LEBs)
UBIFS (ubi0:0): reserved for root: 0 bytes (0 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 757FC57B-3216-4972-B01B-2662A2BD617B, small LPT model
VFS: Mounted root (ubifs filesystem) readonly on device 0:14.
devtmpfs: mounted
Freeing unused kernel memory: 424K (c07ca000 - c0834000)
This architecture does not have kernel memory protection.
systemd[1]: System time before build time, advancing clock.
systemd[1]: systemd 230 running in system mode. (-PAM -AUDIT -SELINUX -IMA -APPARMOR -SMACK -SYSVINIT -UTMP -LIBCRYPTSETUP -GCRYPT -GNUTLS -ACL -XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -IDN)
systemd[1]: Detected architecture arm.

Welcome to PTXdist / EAG-ecu02!

systemd[1]: Set hostname to <ecu02>.
systemd[1]: Initializing machine ID from random generator.
systemd[1]: Installed transient /etc/machine-id file.
systemd[1]: systemd-udev-trigger.service: Cannot add dependency job, ignoring: Unit systemd-udev-trigger.service is masked.
systemd[1]: Listening on udev Control Socket.
[  OK  ] Listening on udev Control Socket.
systemd[1]: Created slice System Slice.
[  OK  ] Created slice System Slice.
systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[  OK  ] Started Dispatch Password Requests to Console Directory Watch.
systemd[1]: Listening on udev Kernel Socket.
[  OK  ] Listening on udev Kernel Socket.
[  OK  ] Listening on Journal Socket.
         Mounting Debug File System...
         Starting Remount Root and Kernel File Systems...
         Mounting POSIX Message Queue File System...
         Starting Load Kernel Modules...
         Starting Attach data ubi partition...
         Starting Create list of required st... nodes for the current kernel...
[  OK  ] Listening on Journal Socket (/dev/log).
ubi1: attaching mtd4
ecu_comp_cap: loading out-of-tree module taints kernel.
[  OK  ] Reached target Swap.
### Flush-Cache module ###
         Starting Journal Service...
[  OK  ] Mounted Debug File System.
[  OK  ] Mounted POSIX Message Queue File System.
[  OK  ] Started Remount Root and Kernel File Systems.
[  OK  ] Started Load Kernel Modules.
[  OK  ] Started Create list of required sta...ce nodes for the current kernel.
         Starting Create Static Device Nodes in /dev...
         Starting Apply Kernel Variables...
ubi1: scanning is finished
ubi1: attached mtd4 (name "var", size 43 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 512
ubi1: VID header offset: 512 (aligned 512), data offset: 2048
ubi1: good PEBs: 345, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 2, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 1444650347
ubi1: available PEBs: 13, total reserved PEBs: 332, PEBs reserved for bad PEB handling: 16
ubi1: background thread "ubi_bgt1d" started, PID 94
[  OK  ] Started Apply Kernel Variables.
[  OK  ] Started Attach data ubi partition.
random: crng init done
         Starting Check and create ubi partitions...
[  OK  ] Started Create Static Device Nodes in /dev.
         Starting udev Kernel Device Manager...
[  OK  ] Reached target Local File Systems (Pre).
         Mounting /var/lib...
         Mounting /media...
         Mounting /var/log...
         Mounting /var/tmp...
         Mounting /tmp...
         Mounting /var/lock...
         Mounting /var/run...
[  OK  ] Mounted /tmp.
[  OK  ] Mounted /media.
[  OK  ] Mounted /var/lib.
[  OK  ] Mounted /var/log.
[  OK  ] Mounted /var/lock.
[  OK  ] Mounted /var/tmp.
[  OK  ] Mounted /var/run.
         Mounting /var/lib/nfs...
[  OK  ] Mounted /var/lib/nfs.
[  OK  ] Started Check and create ubi partitions.
         Mounting Mount /var/dyn partition...
         Mounting Mount /var/stat partition...
[  OK  ] Started udev Kernel Device Manager.
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 122
UBIFS (ubi1:1): background thread "ubifs_bgt1_1" started, PID 124
UBIFS (ubi1:0): recovery needed
UBIFS (ubi1:1): recovery needed
UBIFS (ubi1:1): recovery completed
UBIFS (ubi1:1): UBIFS: mounted UBI device 1, volume 1, name "stat"
UBIFS (ubi1:1): LEB size: 129024 bytes (126 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:1): FS size: 18837504 bytes (17 MiB, 146 LEBs), journal size 1032193 bytes (0 MiB, 7 LEBs)
UBIFS (ubi1:1): reserved for root: 889741 bytes (868 KiB)
UBIFS (ubi1:1): media format: w4/r0 (latest is w4/r0), UUID A9BBEFB1-69F3-413A-A1E1-880855BDAB81, small LPT model
UBIFS (ubi1:0): recovery completed
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "dyn"
UBIFS (ubi1:0): LEB size: 129024 bytes (126 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 18837504 bytes (17 MiB, 146 LEBs), journal size 1032193 bytes (0 MiB, 7 LEBs)
UBIFS (ubi1:0): reserved for root: 889741 bytes (868 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID 8976A6DC-7321-4CB5-839D-12C83A904BEA, small LPT model
systemd[1]: Mounted Mount /var/stat partition.
[  OK  ] Mounted Mount /var/stat partition.
systemd[1]: Mounted Mount /var/dyn partition.
[  OK  ] Mounted Mount /var/dyn partition.
systemd[1]: Started Journal Service.
[  OK  ] Started Journal Service.
         Starting Flush Journal to Persistent Storage...
[  OK  ] Reached target Local File Systems.
systemd-journald[91]: Received request to flush runtime journal from PID 1
[  OK  ] Started Flush Journal to Persistent Storage.
         Starting Create Volatile Files and Directories...
[FAILED] Failed to start Create Volatile Files and Directories.
See 'systemctl status systemd-tmpfiles-setup.service' for details.
         Starting Network Time Synchronization...
[  OK  ] Started Network Time Synchronization.
[  OK  ] Reached target System Time Synchronized.
[  OK  ] Reached target System Initialization.
[  OK  ] Reached target System Update.
         Starting First boot services...
systemd-rc-once[132]: remounting root rw...mounting rootfs writable
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 136
systemd-rc-once[132]: done
systemd-rc-once[132]: running rc.once.d services...
systemd-rc-once[132]: running restore-etc ...
systemd-rc-once[132]: No backup found in: /var/dyn/backup_etc
systemd: 45 output lines suppressed due to ratelimiting
systemd-rc-once[132]: remounting root ro...done
Generic PHY 50038000.etherne:19: attached PHY driver [Generic PHY] (mii_bus:phy_addr=50038000.etherne:19, irq=-1)
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready

 _____    _    ____
| ____|  / `  / ___|
|  _|   / _ `| |  _
| |___ / ___ ` |_| |
|_____/_/   `_`____|

                  ___ ____
  ___  ___ _   _ / _ `___ `
 / _ `/ __| | | | | | |__) |
|  __/ (__| |_| | |_| / __/
 `___|`___|`__,_|`___/_____|


OSELAS(R)-ecu02-V2.4.6 / ecu02-2012.10.0
ptxdist-2016.06.1/2020-08-26T15:44:49+0200

ecu02 login: fec 50038000.ethernet eth0: Link is Up - 100Mbps/Half - flow control off
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready

 _____    _    ____
| ____|  / `  / ___|
|  _|   / _ `| |  _
| |___ / ___ ` |_| |
|_____/_/   `_`____|

                  ___ ____
  ___  ___ _   _ / _ `___ `
 / _ `/ __| | | | | | |__) |
|  __/ (__| |_| | |_| / __/
 `___|`___|`__,_|`___/_____|


OSELAS(R)-ecu02-V2.4.6 / ecu02-2012.10.0
ptxdist-2016.06.1/2020-08-26T15:44:49+0200

ecu02 login: root
Password:
running /etc/profile.local
Loading /usr/share/keymaps/i386/qwertz/de.map.gz
root 22:00:29 : ~ # uname -a
Linux ecu02 4.9.0-g9398d97fa4b7 #1 2016-06-01 armv5tejl GNU/Linux