barebox:/ reset barebox 2016.06.0-EAG_2.02-g9917fe052de8 #1 Wed Sep 2 15:12:44 CEST 2020 Board: Eckelmann AG ECU02 mdio_bus: miibus0: probed nand: ONFI flash detected nand: NAND device: Manufacturer ID: 0x2c, Chip ID: 0xb1 (Micron MT29F1G16ABBEAH4), 128MiB, page size: 2048, OOB size: 64 Bad block table found at page 65472, version 0x01 Bad block table found at page 65408, version 0x01 m25p80 m25p80@20: mr25h256 (32 Kbytes) imx-usb 53ff4400.usb: USB EHCI 1.00 netconsole: registered as netconsole-1 malloc space: 0x83efde40 -> 0x87dfbc7f (size 63 MiB) running /env/bin/init... Check if Memory is flashbased ... __PASS__ USB: scanning bus for devices... Bus 001 Device 001: ID 0000:0000 EHCI Host Controller 1 USB Device(s) found USB: scanning bus for devices... 1 USB Device(s) found running automount command 'usb && if [ -e /dev/disk0.0 ]; then mount /dev/disk0.0 /mnt/usbstorage; elif [ -e /dev/disk0 ]; then mount /dev/disk0 /mnt/usbstorage; fi' failed USB: scanning bus for devices... 1 USB Device(s) found running automount command 'usb && if [ -e /dev/disk0.0 ]; then mount /dev/disk0.0 /mnt/usbstorage; elif [ -e /dev/disk0 ]; then mount /dev/disk0 /mnt/usbstorage; fi' failed USB: scanning bus for devices... 1 USB Device(s) found running automount command 'usb && if [ -e /dev/disk0.0 ]; then mount /dev/disk0.0 /mnt/usbstorage; elif [ -e /dev/disk0 ]; then mount /dev/disk0 /mnt/usbstorage; fi' failed Hit m for menu or any other key to stop autoboot: 1 blspec: blspec_scan_directory: nand loader/entries USB: scanning bus for devices... 1 USB Device(s) found USB: scanning bus for devices... 1 USB Device(s) found running automount command 'usb && if [ -e /dev/disk0.0 ]; then mount /dev/disk0.0 /mnt/usbstorage; elif [ -e /dev/disk0 ]; then mount /dev/disk0 /mnt/usbstorage; fi' failed USB: scanning bus for devices... 1 USB Device(s) found running automount command 'usb && if [ -e /dev/disk0.0 ]; then mount /dev/disk0.0 /mnt/usbstorage; elif [ -e /dev/disk0 ]; then mount /dev/disk0 /mnt/usbstorage; fi' failed Could not find Imagefile: /mnt/usbstorage/ecu02/root.ubi UBI: scanning is finished UBI warning: print_rsvd_warning: cannot reserve enough PEBs for bad PEB handling, reserved 16, need 20 UBI: registering /dev/nand0.root.ubi UBI: registering root as /dev/nand0.root.ubi.root UBI: attached mtd0 (name "nand0.root", size 80 MiB) to ubi0 UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "root", R/O mode UBIFS (ubi0:0): LEB size: 129024 bytes (126 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes UBIFS (ubi0:0): FS size: 78317568 bytes (74 MiB, 607 LEBs), journal size 9033728 bytes (8 MiB, 71 LEBs) UBIFS (ubi0:0): reserved for root: 0 bytes (0 KiB) UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 83ff209c, small LPT model Loading ARM Linux zImage '/mnt/nand0-root/boot/zImage' commandline: console=ttymxc0,115200n8 lpj=995328 mtdparts=mxc_nand:1024k(barebox),1024k(bareboxenv),2432k(history),80M(root),-(var) console=null ro root=ubi0_0 rootfstype=ubifs ubi.mtd=3 Uncompressing Linux... done, booting the kernel. Booting Linux on physical CPU 0x0 Linux version 4.9.0-g9398d97fa4b7 (ptxdist@ptxdist) (gcc version 5.4.0 (OSELAS.Toolchain-2016.06.0) ) #1 2016-06-01 CPU: ARM926EJ-S [41069264] revision 4 (ARMv5TEJ), cr=0005317f CPU: VIVT data cache, VIVT instruction cache OF: fdt:Machine model: Eckelmann AG ECU02 Memory policy: Data cache writeback Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 Kernel command line: console=ttymxc0,115200n8 lpj=995328 mtdparts=mxc_nand:1024k(barebox),1024k(bareboxenv),2432k(history),80M(root),-(var) console=null ro root=ubi0_0 rootfstype=ubifs ubi.mtd=3 PID hash table entries: 512 (order: -1, 2048 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 120656K/131072K available (6090K kernel code, 525K rwdata, 1336K rodata, 424K init, 247K bss, 10416K reserved, 0K cma-reserved) Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xffc00000 - 0xfff00000 (3072 kB) vmalloc : 0xc8800000 - 0xff800000 ( 880 MB) lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .text : 0xc0008000 - 0xc05faef8 (6092 kB) .init : 0xc07ca000 - 0xc0834000 ( 424 kB) .data : 0xc0834000 - 0xc08b7798 ( 526 kB) .bss : 0xc08b7798 - 0xc08f5458 ( 248 kB) NR_IRQS:16 nr_irqs:16 16 MXC IRQ initialized Switching to timer-based delay loop, resolution 15ns sched_clock: 32 bits at 66MHz, resolution 15ns, wraps every 32292987384ns clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 28740758601 ns Console: colour dummy device 80x30 Calibrating delay loop (skipped) preset value.. 398.13 BogoMIPS (lpj=995328) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) CPU: Testing write buffer coherency: ok ftrace: allocating 21751 entries in 64 pages Setting up static identity map for 0x80008400 - 0x8000843c devtmpfs: initialized VFP support v0.3: not present clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302231375000 ns pinctrl core: initialized pinctrl subsystem NET: Registered protocol family 16 DMA: preallocated 256 KiB pool for atomic coherent allocations cpuidle: using governor ladder No ATAGs? imx25-pinctrl 43fac000.iomuxc: initialized IMX pinctrl driver SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb i2c i2c-0: IMX I2C adapter registered i2c i2c-0: can't use DMA, using PIO instead. pca953x 2-0020: failed reading register i2c i2c-2: IMX I2C adapter registered i2c i2c-2: can't use DMA, using PIO instead. pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti PTP clock support registered clocksource: Switched to clocksource mxc_timer1 NET: Registered protocol family 2 TCP established hash table entries: 1024 (order: 0, 4096 bytes) TCP bind hash table entries: 1024 (order: 0, 4096 bytes) TCP: Hash tables configured (established 1024 bind 1024) UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. futex hash table entries: 256 (order: -1, 3072 bytes) workingset: timestamp_bits=30 max_order=15 bucket_order=0 NFS: Registering the id_resolver key type Key type id_resolver registered Key type id_legacy registered nfs4filelayout_init: NFSv4 File Layout Driver Registering... Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) io scheduler noop registered io scheduler cfq registered (default) imx-sdma 53fd4000.sdma: Direct firmware load for imx/sdma/sdma-imx25.bin failed with error -2 imx-sdma 53fd4000.sdma: external firmware not found, using ROM firmware 43f90000.serial: ttymxc0 at MMIO 0x43f90000 (irq = 61, base_baud = 4156250) is a IMX console [ttymxc0] enabled 43f94000.serial: ttymxc1 at MMIO 0x43f94000 (irq = 48, base_baud = 4156250) is a IMX 50008000.serial: ttymxc3 at MMIO 0x50008000 (irq = 21, base_baud = 4156250) is a IMX loop: module loaded nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xb1 nand: Micron MT29F1G16ABBEAH4 nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 Bad block table found at page 65472, version 0x01 Bad block table found at page 65408, version 0x01 5 cmdlinepart partitions found on MTD device mxc_nand Creating 5 MTD partitions on "mxc_nand": 0x000000000000-0x000000100000 : "barebox" 0x000000100000-0x000000200000 : "bareboxenv" 0x000000200000-0x000000460000 : "history" 0x000000460000-0x000005460000 : "root" 0x000005460000-0x000008000000 : "var" spi_imx 43fa4000.cspi: probed libphy: Fixed MDIO Bus: probed CAN device driver interface flexcan 43f88000.can: device registered (reg_base=c891c000, irq=59) flexcan 43f8c000.can: device registered (reg_base=c8924000, irq=60) fec 50038000.ethernet (unnamed net_device) (uninitialized): Invalid MAC address: 00:00:00:00:00:00 fec 50038000.ethernet (unnamed net_device) (uninitialized): Using random MAC address: c2:4a:eb:d1:b1:ea random: fast init done libphy: fec_enet_mii_bus: probed usbcore: registered new interface driver rt2800usb usbcore: registered new interface driver rtl8192cu ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-mxc: Freescale On-Chip EHCI Host driver usbcore: registered new interface driver usb-storage ci_hdrc ci_hdrc.1: doesn't support gadget ci_hdrc ci_hdrc.1: EHCI Host Controller ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected rtc-pcf2123 spi0.3: clock was stopped. Time is not valid rtc-pcf2123 spi0.3: spiclk 1039 KHz. rtc-pcf2123 spi0.3: clock was stopped. Time is not valid rtc-pcf2123 spi0.3: rtc core: registered rtc-pcf2123 as rtc0 i2c /dev entries driver ad7414 0-0049: chip found sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman sdhci-pltfm: SDHCI platform and OF driver helper mmc0: SDHCI controller on 53fb8000.esdhc [53fb8000.esdhc] using DMA usbcore: registered new interface driver usbhid usbhid: USB HID core driver NET: Registered protocol family 10 sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver NET: Registered protocol family 17 can: controller area network core (rev 20120528 abi 9) NET: Registered protocol family 29 Key type dns_resolver registered ubi0: attaching mtd3 ubi0: scanning is finished ubi0 warning: ubi_eba_init: cannot reserve enough PEBs for bad PEB handling, reserved 18, need 20 ubi0: attached mtd3 (name "root", size 80 MiB) ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 512 ubi0: VID header offset: 512 (aligned 512), data offset: 2048 ubi0: good PEBs: 640, bad PEBs: 0, corrupted PEBs: 0 ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128 ubi0: max/mean erase counter: 14/8, WL threshold: 4096, image sequence number: 24264 ubi0: available PEBs: 0, total reserved PEBs: 640, PEBs reserved for bad PEB handling: 18 ubi0: background thread "ubi_bgt0d" started, PID 64 rtc-pcf2123 spi0.3: clock was stopped. Time is not valid rtc-pcf2123 spi0.3: hctosys: unable to read the hardware clock UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "root", R/O mode UBIFS (ubi0:0): LEB size: 129024 bytes (126 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes UBIFS (ubi0:0): FS size: 78317568 bytes (74 MiB, 607 LEBs), journal size 9033728 bytes (8 MiB, 71 LEBs) UBIFS (ubi0:0): reserved for root: 0 bytes (0 KiB) UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 757FC57B-3216-4972-B01B-2662A2BD617B, small LPT model VFS: Mounted root (ubifs filesystem) readonly on device 0:14. devtmpfs: mounted Freeing unused kernel memory: 424K (c07ca000 - c0834000) This architecture does not have kernel memory protection. systemd[1]: System time before build time, advancing clock. systemd[1]: systemd 230 running in system mode. (-PAM -AUDIT -SELINUX -IMA -APPARMOR -SMACK -SYSVINIT -UTMP -LIBCRYPTSETUP -GCRYPT -GNUTLS -ACL -XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -IDN) systemd[1]: Detected architecture arm. Welcome to PTXdist / EAG-ecu02! systemd[1]: Set hostname to . systemd[1]: Initializing machine ID from random generator. systemd[1]: Installed transient /etc/machine-id file. systemd[1]: systemd-udev-trigger.service: Cannot add dependency job, ignoring: Unit systemd-udev-trigger.service is masked. systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. systemd[1]: Created slice System Slice. [ OK ] Created slice System Slice. systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password Requests to Console Directory Watch. systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ OK ] Listening on Journal Socket. Mounting Debug File System... Starting Remount Root and Kernel File Systems... Mounting POSIX Message Queue File System... Starting Load Kernel Modules... Starting Attach data ubi partition... Starting Create list of required st... nodes for the current kernel... [ OK ] Listening on Journal Socket (/dev/log). ubi1: attaching mtd4 ecu_comp_cap: loading out-of-tree module taints kernel. [ OK ] Reached target Swap. ### Flush-Cache module ### Starting Journal Service... [ OK ] Mounted Debug File System. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Started Remount Root and Kernel File Systems. [ OK ] Started Load Kernel Modules. [ OK ] Started Create list of required sta...ce nodes for the current kernel. Starting Create Static Device Nodes in /dev... Starting Apply Kernel Variables... ubi1: scanning is finished ubi1: attached mtd4 (name "var", size 43 MiB) ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 512 ubi1: VID header offset: 512 (aligned 512), data offset: 2048 ubi1: good PEBs: 345, bad PEBs: 4, corrupted PEBs: 0 ubi1: user volume: 2, internal volumes: 1, max. volumes count: 128 ubi1: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 1444650347 ubi1: available PEBs: 13, total reserved PEBs: 332, PEBs reserved for bad PEB handling: 16 ubi1: background thread "ubi_bgt1d" started, PID 94 [ OK ] Started Apply Kernel Variables. [ OK ] Started Attach data ubi partition. random: crng init done Starting Check and create ubi partitions... [ OK ] Started Create Static Device Nodes in /dev. Starting udev Kernel Device Manager... [ OK ] Reached target Local File Systems (Pre). Mounting /var/lib... Mounting /media... Mounting /var/log... Mounting /var/tmp... Mounting /tmp... Mounting /var/lock... Mounting /var/run... [ OK ] Mounted /tmp. [ OK ] Mounted /media. [ OK ] Mounted /var/lib. [ OK ] Mounted /var/log. [ OK ] Mounted /var/lock. [ OK ] Mounted /var/tmp. [ OK ] Mounted /var/run. Mounting /var/lib/nfs... [ OK ] Mounted /var/lib/nfs. [ OK ] Started Check and create ubi partitions. Mounting Mount /var/dyn partition... Mounting Mount /var/stat partition... [ OK ] Started udev Kernel Device Manager. UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 122 UBIFS (ubi1:1): background thread "ubifs_bgt1_1" started, PID 124 UBIFS (ubi1:0): recovery needed UBIFS (ubi1:1): recovery needed UBIFS (ubi1:1): recovery completed UBIFS (ubi1:1): UBIFS: mounted UBI device 1, volume 1, name "stat" UBIFS (ubi1:1): LEB size: 129024 bytes (126 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes UBIFS (ubi1:1): FS size: 18837504 bytes (17 MiB, 146 LEBs), journal size 1032193 bytes (0 MiB, 7 LEBs) UBIFS (ubi1:1): reserved for root: 889741 bytes (868 KiB) UBIFS (ubi1:1): media format: w4/r0 (latest is w4/r0), UUID A9BBEFB1-69F3-413A-A1E1-880855BDAB81, small LPT model UBIFS (ubi1:0): recovery completed UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "dyn" UBIFS (ubi1:0): LEB size: 129024 bytes (126 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes UBIFS (ubi1:0): FS size: 18837504 bytes (17 MiB, 146 LEBs), journal size 1032193 bytes (0 MiB, 7 LEBs) UBIFS (ubi1:0): reserved for root: 889741 bytes (868 KiB) UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID 8976A6DC-7321-4CB5-839D-12C83A904BEA, small LPT model systemd[1]: Mounted Mount /var/stat partition. [ OK ] Mounted Mount /var/stat partition. systemd[1]: Mounted Mount /var/dyn partition. [ OK ] Mounted Mount /var/dyn partition. systemd[1]: Started Journal Service. [ OK ] Started Journal Service. Starting Flush Journal to Persistent Storage... [ OK ] Reached target Local File Systems. systemd-journald[91]: Received request to flush runtime journal from PID 1 [ OK ] Started Flush Journal to Persistent Storage. Starting Create Volatile Files and Directories... [FAILED] Failed to start Create Volatile Files and Directories. See 'systemctl status systemd-tmpfiles-setup.service' for details. Starting Network Time Synchronization... [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Time Synchronized. [ OK ] Reached target System Initialization. [ OK ] Reached target System Update. Starting First boot services... systemd-rc-once[132]: remounting root rw...mounting rootfs writable UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 136 systemd-rc-once[132]: done systemd-rc-once[132]: running rc.once.d services... systemd-rc-once[132]: running restore-etc ... systemd-rc-once[132]: No backup found in: /var/dyn/backup_etc systemd: 45 output lines suppressed due to ratelimiting systemd-rc-once[132]: remounting root ro...done Generic PHY 50038000.etherne:19: attached PHY driver [Generic PHY] (mii_bus:phy_addr=50038000.etherne:19, irq=-1) IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready _____ _ ____ | ____| / ` / ___| | _| / _ `| | _ | |___ / ___ ` |_| | |_____/_/ `_`____| ___ ____ ___ ___ _ _ / _ `___ ` / _ `/ __| | | | | | |__) | | __/ (__| |_| | |_| / __/ `___|`___|`__,_|`___/_____| OSELAS(R)-ecu02-V2.4.6 / ecu02-2012.10.0 ptxdist-2016.06.1/2020-08-26T15:44:49+0200 ecu02 login: fec 50038000.ethernet eth0: Link is Up - 100Mbps/Half - flow control off IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready _____ _ ____ | ____| / ` / ___| | _| / _ `| | _ | |___ / ___ ` |_| | |_____/_/ `_`____| ___ ____ ___ ___ _ _ / _ `___ ` / _ `/ __| | | | | | |__) | | __/ (__| |_| | |_| / __/ `___|`___|`__,_|`___/_____| OSELAS(R)-ecu02-V2.4.6 / ecu02-2012.10.0 ptxdist-2016.06.1/2020-08-26T15:44:49+0200 ecu02 login: root Password: running /etc/profile.local Loading /usr/share/keymaps/i386/qwertz/de.map.gz root 22:00:29 : ~ # uname -a Linux ecu02 4.9.0-g9398d97fa4b7 #1 2016-06-01 armv5tejl GNU/Linux