pastebin - collaborative debugging tool
eckelmann.kpaste.net RSS


ukl/development ecu02 boot hangs 2020-09-02
Posted by Anonymous on Wed 2nd Sep 2020 12:52
raw | new post

  1. barebox:/ loadenv -d
  2. loading environment from defaultenv
  3. barebox:/ saveenv
  4. saving environment
  5. barebox:/ reset
  6.  
  7.  
  8. barebox 2016.06.0-EAG_2.02-g98782b23275b #1 Wed Aug 26 16:18:47 CEST 2020
  9.  
  10.  
  11. Board: Eckelmann AG ECU02
  12. mdio_bus: miibus0: probed
  13. nand: ONFI flash detected
  14. nand: NAND device: Manufacturer ID: 0x2c, Chip ID: 0xb1 (Micron MT29F1G16ABBEAH4), 128MiB, page size: 2048, OOB size: 64
  15. Bad block table found at page 65472, version 0x01
  16. Bad block table found at page 65408, version 0x01
  17. m25p80 m25p80@20: mr25h256 (32 Kbytes)
  18. imx-usb 53ff4400.usb: USB EHCI 1.00
  19. netconsole: registered as netconsole-1
  20. malloc space: 0x83efde40 -> 0x87dfbc7f (size 63 MiB)
  21. running /env/bin/init...
  22. Check if Memory is flashbased ...
  23. __PASS__
  24. ==> Saving Defaultenv ...
  25. saving environment
  26. USB: scanning bus for devices...
  27. Bus 001 Device 001: ID 0000:0000 EHCI Host Controller
  28. 1 USB Device(s) found
  29. USB: scanning bus for devices...
  30. 1 USB Device(s) found
  31. running automount command 'usb && if [ -e /dev/disk0.0 ]; then mount /dev/disk0.0 /mnt/usbstorage; elif [ -e /dev/disk0 ]; then mount /dev/disk0 /mnt/usbstorage; fi' failed
  32. USB: scanning bus for devices...
  33. 1 USB Device(s) found
  34. running automount command 'usb && if [ -e /dev/disk0.0 ]; then mount /dev/disk0.0 /mnt/usbstorage; elif [ -e /dev/disk0 ]; then mount /dev/disk0 /mnt/usbstorage; fi' failed
  35. USB: scanning bus for devices...
  36. 1 USB Device(s) found
  37. running automount command 'usb && if [ -e /dev/disk0.0 ]; then mount /dev/disk0.0 /mnt/usbstorage; elif [ -e /dev/disk0 ]; then mount /dev/disk0 /mnt/usbstorage; fi' failed
  38.  
  39. Hit m for menu or any other key to stop autoboot:  0
  40. blspec: blspec_scan_directory: nand loader/entries
  41. USB: scanning bus for devices...
  42. 1 USB Device(s) found
  43. USB: scanning bus for devices...
  44. 1 USB Device(s) found
  45. running automount command 'usb && if [ -e /dev/disk0.0 ]; then mount /dev/disk0.0 /mnt/usbstorage; elif [ -e /dev/disk0 ]; then mount /dev/disk0 /mnt/usbstorage; fi' failed
  46. USB: scanning bus for devices...
  47. 1 USB Device(s) found
  48. running automount command 'usb && if [ -e /dev/disk0.0 ]; then mount /dev/disk0.0 /mnt/usbstorage; elif [ -e /dev/disk0 ]; then mount /dev/disk0 /mnt/usbstorage; fi' failed
  49. Could not find Imagefile: /mnt/usbstorage/ecu02/root.ubi
  50. UBI: scanning is finished
  51. UBI warning: print_rsvd_warning: cannot reserve enough PEBs for bad PEB handling, reserved 16, need 20
  52. UBI: registering /dev/nand0.root.ubi
  53. UBI: registering root as /dev/nand0.root.ubi.root
  54. UBI: attached mtd0 (name "nand0.root", size 80 MiB) to ubi0
  55. UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "root", R/O mode
  56. UBIFS (ubi0:0): LEB size: 129024 bytes (126 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
  57. UBIFS (ubi0:0): FS size: 78317568 bytes (74 MiB, 607 LEBs), journal size 9033728 bytes (8 MiB, 71 LEBs)
  58. UBIFS (ubi0:0): reserved for root: 0 bytes (0 KiB)
  59. UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 83effabc, small LPT model
  60.  
  61. Loading ARM Linux zImage '/mnt/nand0-root/boot/zImage'
  62. commandline:  console=ttymxc0,115200n8   lpj=995328 mtdparts=mxc_nand:1024k(barebox),1024k(bareboxenv),2432k(history),80M(root),-(var) console=null ro root=ubi0_0 rootfstype=ubifs ubi.mtd=3
  63. arch_number: 8016

Submit a correction or amendment below (click here to make a fresh posting)
After submitting an amendment, you'll be able to view the differences between the old and new posts easily.

Syntax highlighting:

To highlight particular lines, prefix each line with {%HIGHLIGHT}




All content is user-submitted.
The administrators of this site (kpaste.net) are not responsible for their content.
Abuse reports should be emailed to us at