pastebin - collaborative debugging tool
eckelmann.kpaste.net RSS


quantron boot log mit wifi, per ukl request #002
Posted by Anonymous on Wed 22nd May 2019 10:50
raw | new post

  1. [  OK  ] Listening on Journal Socket.
  2. systemd[1]: Listening on Journal Socket.
  3. systemd[1]: Starting udev Coldplug TTY Devices for Getty...
  4.          Starting udev Coldplug TTY Devices for Getty...
  5. systemd[1]: Starting Apply Kernel Variables...
  6.          Starting Apply Kernel Variables...
  7. systemd[1]: Starting Journal Service...
  8.          Starting Journal Service...
  9. [  OK  ] Started Journal Service.
  10. systemd[1]: Started Journal Service.
  11. systemd[1]: Starting Load Kernel Modules...
  12.          Starting Load Kernel Modules...
  13. systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
  14. systemd[1]: Started Set Up Additional Binary Formats.
  15. systemd[1]: Starting Create static device nodes in /dev...
  16.          Starting Create static device nodes in /dev...
  17. systemd[1]: Starting Attach data ubi partition...
  18.          Starting Attach data ubi partition...
  19. systemd[1]: Starting File System Check on Root Device...
  20.          Starting File System Check on Root Device...
  21. [  OK  ] Started Apply Kernel Variables.
  22. UBI: attaching mtd4 to ubi1
  23. [  OK  ] Started File System Check on Root Device.
  24.          Starting Remount Root and Kernel File Systems...
  25. ads7953_init
  26. systemd-journald[583]: Failed to resolve 'systemd-journal' group: No such process
  27. [  OK  ] Started Create static device nodes in /dev.
  28. [  OK  ] Started udev Coldplug TTY Devices for Getty.
  29.          Starting udev Kernel Device Manager...
  30. mmc_init() called
  31. qa_driver_init() called
  32. systemd-modules-load[586]: Inserted module 'qadriver'
  33. [  OK  ] Started Load Kernel Modules.
  34. systemd-udevd[615]: starting version 204
  35. [  OK  ] Started udev Kernel Device Manager.
  36. UBI: scanning is finished
  37. [  OK  ] Started Remount Root and Kernel File Systems.
  38. [  OK  ] Reached target Local File Systems (Pre).
  39.          Mounting /var/tmp...
  40.          Mounting /var/lock...
  41. UBI: attached mtd4 (name "var", size 43 MiB) to ubi1
  42. UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
  43.          UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 512
  44. Mounting /var/run...
  45. UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
  46. UBI: good PEBs: 347, bad PEBs: 2, corrupted PEBs: 0
  47. UBI: user volume: 2, internal volumes: 1, max. volumes count: 128
  48.          UBI: max/mean erase counter: 78/40, WL threshold: 4096, image sequence number: 22633
  49. Mounting /var/log...
  50. UBI: available PEBs: 87, total reserved PEBs: 260, PEBs reserved for bad PEB handling: 18
  51. UBI: background thread "ubi_bgt1d" started, PID 649
  52.          Mounting /var/lib...
  53.          Mounting /media...
  54.          Mounting /tmp...
  55. [  OK  ] Started Attach data ubi partition.
  56. [  OK  ] Mounted /var/tmp.
  57. [  OK  ] Mounted /var/lock.
  58. [  OK  ] Mounted /var/run.
  59. [  OK  ] Mounted /var/log.
  60.          Starting Check and create ubi partitions...
  61. [  OK  ] Found device /dev/ttymxc4.
  62. [  OK  ] Mounted /media.
  63. [  OK  ] Mounted /var/lib.
  64. [  OK  ] Mounted /tmp.
  65. [  OK  ] Started Check and create ubi partitions.
  66.          Mounting Mount /var/stat partition...
  67.          Mounting Mount /var/dyn partition...
  68. UBIFS: background thread "ubifs_bgt1_1" started, PID 689
  69. UBIFS: background thread "ubifs_bgt1_0" started, PID 691
  70. UBIFS: mounted UBI device 1, volume 1, name "stat"
  71. UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
  72. UBIFS: FS size: 13840384 bytes (13 MiB, 109 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs)
  73. UBIFS: reserved for root: 653715 bytes (638 KiB)
  74. UBIFS: media format: w4/r0 (latest is w4/r0), UUID 60DE9B53-3598-455A-9D47-16DF83A21088, small LPT model
  75. UBIFS: mounted UBI device 1, volume 0, name "dyn"
  76. [  OK  ] Mounted Mount /var/stat partitUBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
  77. ion.
  78. UBIFS: FS size: 13840384 bytes (13 MiB, 109 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs)
  79. UBIFS: reserved for root: 653715 bytes (638 KiB)
  80. UBIFS: media format: w4/r0 (latest is w4/r0), UUID CF1AD484-262D-439D-9FB3-B208D935F5A6, small LPT model
  81. [  OK  ] Mounted Mount /var/dyn partition.
  82. [  OK  ] Reached target Local File Systems.
  83.          Starting Recreate Volatile Files and Directories...
  84. [  OK  ] Started Recreate Volatile Files and Directories.
  85. [  OK  ] Reached target System Initialization.
  86. [  OK  ] Listening on sshd.socket.
  87. [  OK  ] Listening on D-Bus System Message Bus Socket.
  88. [  OK  ] Reached target Sockets.
  89. [  OK  ] Reached target Basic System.
  90.          Starting Backup service for configuration in /etc...
  91. [  OK  ] Started Backup service for configuration in /etc.
  92.          Starting Mark kernel activated network interfaces as up...
  93.          Starting Serial Getty on ttymxc4...
  94. [  OK  ] Started Serial Getty on ttymxc4.
  95. [  OK  ] Reached target Login Prompts.
  96.          Starting D-Bus System Message Bus...
  97. [  OK  ] Started D-Bus System Message Bus.
  98.          Starting udev Trigger all Massstorage Devices...
  99. [  OK  ] Started udev Trigger all Massstorage Devices.
  100. imx-sdma imx35-sdma: firmware not found
  101. [  OK  ] Started Mark kernel activated network interfaces as up.
  102.          Starting Handle network interface with ifup/ifdown...
  103. fec imx25-fec.0 eth0: no PHY, assuming direct connection to switch
  104. libphy: PHY fixed-0:00 not found
  105. fec imx25-fec.0 eth0: could not attach to PHY
  106. [FAILED] Failed to start Handle network interface with ifup/ifdown.
  107. See 'systemctl status ifupdown.service' for details.
  108. [  OK  ] Reached target Network.
  109. [  OK  ] Reached target Multi-User System.
  110. [  OK  ] Reached target Graphical Interface.
  111.          Starting Say Goodbye to user at Shutdown...
  112.          Starting CoDeSys 3 runtime...
  113. [  OK  ] Started Say Goodbye to user at Shutdown.
  114.  
  115.  _____    _    ____
  116. | ____|  / `  / ___|
  117. |  _|   / _ `| |  _
  118. | |___ / ___ ` |_| |
  119. |_____/_/   `_`____|
  120.  
  121.                   ___  _
  122.   ___  ___ _   _ / _ `/ |
  123.  / _ `/ __| | | | | | | |
  124. |  __/ (__| |_| | |_| | |
  125.  `___|`___|`__,_|`___/|_|
  126.  
  127.  
  128. OSELAS(R)-ecu01-V3.1.7 / ecu01-2012.10.0
  129. ptxdist-2012.10.0/2019-05-15T11:29:00+0200
  130.  
  131. ecu01 login: [  OK  ] Started CoDeSys 3 runtime.
  132. [  OK  ] Reached target Application Mode.
  133. qa_mmc_open()
  134. qa_mmc_release()
  135. qa_mmc_open()
  136. UBIFS: background thread "ubifs_bgt0_0" started, PID 810
  137. UBIFS: background thread "ubifs_bgt0_0" stops
  138.  
  139.  _____    _    ____
  140. | ____|  / `  / ___|
  141. |  _|   / _ `| |  _
  142. | |___ / ___ ` |_| |
  143. |_____/_/   `_`____|
  144.  
  145.                   ___  _
  146.   ___  ___ _   _ / _ `/ |
  147.  / _ `/ __| | | | | | | |
  148. |  __/ (__| |_| | |_| | |
  149.  `___|`___|`__,_|`___/|_|
  150.  
  151.  
  152. OSELAS(R)-ecu01-V3.1.7 / ecu01-2012.10.0
  153. ptxdist-2012.10.0/2019-05-15T11:29:00+0200
  154.  
  155. ecu01 login: root
  156. Password:
  157. running /etc/profile.local
  158. Loading /usr/share/keymaps/i386/qwertz/de.map.gz
  159. root 11:59:37 : ~ # ifconfig
  160. lo        Link encap:Local Loopback  
  161.           inet addr:127.0.0.1  Mask:255.0.0.0
  162.           inet6 addr: ::1/128 Scope:Host
  163.           UP LOOPBACK RUNNING  MTU:65536  Metric:1
  164.           RX packets:12 errors:0 dropped:0 overruns:0 frame:0
  165.           TX packets:12 errors:0 dropped:0 overruns:0 carrier:0
  166.           collisions:0 txqueuelen:0
  167.           RX bytes:628 (628.0 B)  TX bytes:628 (628.0 B)
  168.  
  169. root 11:59:40 : ~ # ifconfig -a
  170. eth0      Link encap:Ethernet  HWaddr 4E:9D:37:73:8F:2C  
  171.           inet addr:172.21.0.31  Bcast:0.0.0.0  Mask:255.255.255.0
  172.           BROADCAST MULTICAST  MTU:1500  Metric:1
  173.           RX packets:0 errors:0 dropped:0 overruns:0 frame:0
  174.           TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
  175.           collisions:0 txqueuelen:1000
  176.           RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
  177.  
  178. lo        Link encap:Local Loopback  
  179.           inet addr:127.0.0.1  Mask:255.0.0.0
  180.           inet6 addr: ::1/128 Scope:Host
  181.           UP LOOPBACK RUNNING  MTU:65536  Metric:1
  182.           RX packets:12 errors:0 dropped:0 overruns:0 frame:0
  183.           TX packets:12 errors:0 dropped:0 overruns:0 carrier:0
  184.           collisions:0 txqueuelen:0
  185.           RX bytes:628 (628.0 B)  TX bytes:628 (628.0 B)
  186.  
  187. sit0      Link encap:IPv6-in-IPv4  
  188.           NOARP  MTU:1480  Metric:1
  189.           RX packets:0 errors:0 dropped:0 overruns:0 frame:0
  190.           TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
  191.           collisions:0 txqueuelen:0
  192.           RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
  193.  
  194. wlan0     Link encap:Ethernet  HWaddr 00:22:88:02:4A:5D  
  195.           BROADCAST MULTICAST  MTU:1500  Metric:1
  196.           RX packets:0 errors:0 dropped:0 overruns:0 frame:0
  197.           TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
  198.           collisions:0 txqueuelen:1000
  199.           RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

Submit a correction or amendment below (click here to make a fresh posting)
After submitting an amendment, you'll be able to view the differences between the old and new posts easily.

Syntax highlighting:

To highlight particular lines, prefix each line with {%HIGHLIGHT}




All content is user-submitted.
The administrators of this site (kpaste.net) are not responsible for their content.
Abuse reports should be emailed to us at